Position & mounting
The European manual specifies ceiling mounting only, preferably towards one end. Use every mounting hole and keep electrical connections outside the enclosure, dry and protected.
ReptiRad — Powered by Alper
ReptiRad 125.
More output. Same slim profile.
A 125W reptile heat panel.
A step up in output, just 18.5mm thick.
125WRated power
18.5 mmCasing thickness
400 × 294 mmPanel footprint
Space, thoughtfully used
Step up the output.
Keep the slim profile.
The ReptiRad 125 pairs an 18.5mm casing with galvanised steel construction and Class II double insulation.
The ReptiRad 125 provides a higher rated output than the 80W model, with a 400 × 294mm footprint. Its casing remains 18.5mm thick. Allow for the larger mounting area when planning your enclosure.
Explore the specifications ↓
Protected against Dust, Misting and Splashing Water
ReptiRad’s IP64-rated casing adds protection against dust and water splashes from any direction.
Operates in up to 99% relative humidity
For terrestrial reptile and amphibian setups, match the heating to the species, enclosure and required temperatures.
Do not spray the panel directly or immerse it in water. Keep misting nozzles directed away from the panel and keep electrical connections dry.
Explore installation & care ↗The details, clearly
ReptiRad 125.
Technical specifications.
Compare all models ↗Panel footprint · Not to scale
400 mm
ReptiRad 125294 mm
18.5 mm casing thickness
Body dimensions only. Allow for mounting, cable routing and the clearances in the installation instructions.- Model
- ReptiRad 125
- Rated power
- 125W
- Dimensions
- 400 × 294 × 18.5mm
40 × 29.4 × 1.85cm - Casing
- Galvanised steel
- Electrical insulation
- Class II · Double insulated
- Manufacturing
- Italy · Alper
- Purchase route
- Retail partners by country
Confirm the regional electrical specification and plug type with your retailer before ordering.
Choose the panel. Then the retailer.
Is 125W right
for your setup?
Enclosure volume is a starting point. Materials, ventilation, room temperature and target temperatures affect the heating requirement too.
Use the size calculator ↗Sizing guide example · Not a guarantee
120 × 60 × 60 cm
432 litres / 0.432 m³
Room approximately 22–24°C125W estimate
Cooler than 22°C option220W to consider
The size calculator uses enclosure-volume sizing bands. Confirm physical fit and the requirements of your complete setup before buying.
Plan before fitting
A complete setup.
Considered from the start.
Thermostat control
Use a compatible dimming or pulse-proportional thermostat rated for your panel. Secure the probe directly below the panel and check the manufacturer’s placement guidance for your version.
Temperature checks
Run the complete setup for at least 24 hours and confirm stable, species-appropriate temperatures before introducing an animal. Prevent contact with dangerously hot surfaces.
Our manufacturing partner
ReptiRad.
Powered by Alper.
Made in Italy with our manufacturing partner, Alper.
Discover the heating technology and manufacturing expertise behind our partnership.
Alper’s certified management systems
- ISO 9001Quality management
- ISO 45001Occupational health & safety
- ISO 14001Environmental management
Before you buy
Your 125W questions.
Answered.
What are the ReptiRad 125 dimensions?
The panel measures 400 × 294 × 18.5mm, or 40 × 29.4 × 1.85cm. These are the panel dimensions, not the full space needed for mounting and installation clearances.
Which enclosure size is the 125W panel suitable for?
There is no single enclosure size that guarantees suitability. Use the metric size calculator for an initial volume-based estimate, then consider enclosure construction, ventilation, ambient temperature and your target temperatures.
What if my room runs cooler than 22°C?
The size calculator includes a cooler-room checkbox. If the base estimate is 125W, it shows the 220W model for consideration. This is a one-model increase, not a heat-loss calculation; contact us for advice if conditions differ substantially from the guide.
Does 125W mean it uses 125 watts all the time?
125W is the rated power. Actual energy use over time depends on how the thermostat operates and how much heating the enclosure requires. We do not give a fixed running-cost estimate without those conditions.
Where can I buy the ReptiRad 125?
Choose your country on the 125W Shop page to find a purchasing destination. Orders and payments are handled by the retailer. Availability, pricing and delivery are confirmed by your chosen retailer.
How do I confirm warranty and regional details?
The supplied European manual states a 24-month warranty. Read the translated warranty information and contact us to confirm the terms and electrical specification for your country.
ReptiRad 125
Your next setup
starts here.
Find purchasing options for the 125W panel in your country.
Shop ReptiRad 125 ↗Before you install
Plan your complete setup.
Choosing your panel
What size reptile heat panel do I need?
Start with your enclosure, then choose the panel. Volume gives you a first estimate; the complete setup determines whether that estimate is suitable.
Read the guide ↗Temperature controlChoosing a thermostat for your ReptiRad heat panel
A thermostat is an essential part of the setup. Choose the correct control mode, check the electrical rating and secure the probe before switching on.
Read the guide ↗Compare your optionsRadiant heat panel vs ceramic heat emitter
Compare the complete installation: the space it needs, how it is controlled and the temperatures it maintains. A wattage label alone cannot answer which setup is right for you.
Read the guide ↗